ASBESTOS TESTING ESSEX · LONDON · SOUTH EAST
Asbestos testing identifies whether a material contains asbestos and which type it is. A small sample is taken under controlled conditions, sealed, labelled and sent to an independent UKAS-accredited laboratory for analysis to ISO/IEC 17025. We do not analyse our own samples: separating who takes the sample from who identifies it is what makes a result stand up to an enforcing authority, an insurer or a buyer’s solicitor. Based in Great Wakering near Southend-on-Sea, we cover Essex, London and the wider South East.
Every bulk sample goes to a UKAS-accredited laboratory accredited to ISO/IEC 17025. We take the samples; we do not identify them.
Samples are taken wet where the material allows, with the area sheeted, the sampling point sealed afterwards and the debris collected, not left behind.
Every sample is logged against its exact location, photographed, and tracked from the building to the laboratory and back into the report you receive.
The certificate states the method, the result and the asbestos type, in the form a contractor, an insurer or an enforcing authority expects.
What It Is
A test answers one question: does this material contain asbestos, and if so, which type. It does not tell you whether the material is dangerous, whether it has to be removed, or what it would cost — those come from condition, location and the risk assessment that sits alongside the result. A positive result on an intact cement sheet in a roof and a positive result on damaged lagging in an occupied plant room are the same two words on a certificate and two completely different problems.
The laboratory identifies the fibre type: chrysotile, amosite, crocidolite or one of the rarer forms. That matters because type and material together determine the regime the work falls under. What the certificate cannot do is speak for anything that was not sampled, which is why a result is read alongside the survey that produced it rather than on its own.
When You Need It
Four situations account for almost every test we are asked to run.
Most samples are taken during a survey, where a material cannot be identified on sight and the register needs a confirmed answer.
A contractor about to open up a wall, lift a floor or take down a ceiling needs to know what is in it, in writing, before the first cut is made.
An Artex ceiling, a garage roof sheet, a vinyl tile or an old flue. One material, one answer, and usually only one short visit to the property.
Something has been drilled, broken or swept up. Identification comes first, because what the material is decides what follows.
On Site
Taking a sample disturbs the material, so the method is the whole job. The area is sheeted, the point is wetted where the material allows it, and a small piece is removed with hand tools rather than anything powered. The debris is collected, the sample is sealed in a double bag and labelled, and the sampling point is sealed over. The surveyor records the exact location, photographs it, and logs the reference that will follow the sample to the laboratory and back into the report.
Bad sampling is worse than none. A sample taken dry with a drill puts fibres into the air of an occupied room; a sample with no location reference produces a certificate that proves something about a building without saying where; a sample taken from the wrong layer of a textured coating can return a negative on a material that does contain asbestos lower down. If you have been offered a test by someone who will not explain their method, that is the question to ask.
Materials
Artex ceilings and walls, common in homes built or refurbished before 2000. Sampled rather than presumed, because the sample must pass through every layer.
Garage roofs, barn sheets, soffits and wall cladding. Usually straightforward to identify, but condition varies enormously and that is what the result gets read against.
Thermoplastic tiles and the black bitumen adhesive beneath them. The tile and the glue are separate materials, and each can carry asbestos independently of the other.
Ceiling tiles, soffits, panels and fire breaks. Easily mistaken for plasterboard on sight, and the distinction decides whether the work that follows is licensed.
Lagging on pipes, boilers and calorifiers, and the rope seals around them. Among the highest-risk materials, so sampling is tightly controlled.
Flue pipes, boiler gaskets, panels behind heaters and in service risers. Small items, easily missed, and routinely found during strip-out rather than during a survey.
If the material you are looking at is not on this list, send a photograph and we will tell you whether it needs a sample.
Results
A result on its own is not an answer. Three things come back together.
The laboratory analysis certificate, stating the method, the sample reference, the result and the fibre type. It attaches to the report.
A positive result is scored for the condition of the material and how likely it is to be disturbed, which decides what happens next.
Manage in place, encapsulate, or remove — with the regime stated, so you know what you are pricing before you price it.
The Legal Duty
The Control of Asbestos Regulations 2012 do not require every material to be tested. Regulation 4 allows a duty holder to presume asbestos is present and manage on that basis, and Regulation 5 requires identification before refurbishment or demolition — but identification can be by analysis or by presumption. The practical difference is cost: presuming means treating a material as asbestos for every piece of work that ever touches it.
Where analysis is done, Approved Code of Practice L143 and HSE guidance HSG264 set out how samples are taken and reported, and the laboratory works to ISO/IEC 17025 under UKAS accreditation. Any work that then disturbs confirmed material brings in the workplace control limit of 0.1 fibres per cubic centimetre over four hours, and where licensed removal follows, clearance to below 0.01 fibres per cubic centimetre before reoccupation. The management side is on our duty to manage asbestos page.
Areas We Cover
Based in Great Wakering near Southend-on-Sea, we cover Essex, London and the wider South East.
We take samples from homes, commercial units, industrial sites, schools and historic buildings across Southend-on-Sea, Rochford, Rayleigh, Basildon, Chelmsford, Brentwood, Colchester and into East London. Where a result confirms asbestos, the same team can carry out air monitoring and the work that follows, so nothing waits on another supplier being appointed.
Get in Touch
Tell us what the material is, where it is and how much of it there is, and send a photograph if you can. We will confirm whether a single sample answers it or whether a survey is the better route, with a fixed price either way. If the material has just been disturbed, call 01702 690 693 rather than waiting for a reply. The contact page and our FAQ cover everything else.
Ora Asbestos Management Ltd
Unit 6, Crouchmans Yard, Poynters Lane,
Great Wakering, Essex, SS3 9TS
Hours: Monday–Saturday, 6am–6pm · Closed Sunday
Standard laboratory turnaround is a few working days from the sample reaching the laboratory. We confirm the turnaround when we quote rather than promising a figure here.
We would rather you did not. Taking a sample disturbs the material, and doing it dry or without controls puts fibres into the air of the room you are standing in. If the material is accessible and intact, photograph it and let us take the sample properly.
That the sample analysed contained no detectable asbestos. It says nothing about any other material in the building, or about the same material elsewhere in it — results apply to what was sampled, at the point it was sampled.
Very little: a piece a few centimetres across is usually enough. For layered materials such as textured coatings the sample has to go through every layer, which is a common reason home-taken samples come back wrong.
An independent UKAS-accredited laboratory, accredited to ISO/IEC 17025 for asbestos bulk analysis. We do not publish the laboratory accreditation number on the website.
No. Asbestos in good condition and out of harm’s way is usually safest managed in place, labelled and recorded on the register. Removal is for damaged material or material in the way of planned work.
Air testing answers a different question — how many fibres are in the air now, not what a material contains. Both have their place, and air monitoring is covered on its own page.
Standard bulk analysis identifies whether asbestos is present and which type. It is not a quantification. If quantification is what you actually need, we will tell you.
Cookies on this site
We use strictly necessary cookies to make this site work. With your permission we would also like to use analytics cookies to see how the site is used so we can improve it. You can change your choice at any time. See our cookie policy.